The right accessories are the perfect addition to our pallet conveyor systems. In some areas, they make the handling our systems easier. The following accessories are available:

  • Adjustable loading ram protection with centring aid and stacker control
  • Portal for accommodating scanners, barcode and reading devices
  • Contour check device and muting frame
  • Weighing devices and load cells
  • Protective devices and protection guards
HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

A traversing carriage is necessary to distribute funds to a larger number of conveyor tracks on the same level. Traversing carriages can be either fully self-propelled or pulled by toothed belts. The drive is located directly on the traversing carriage and is a frequency-controlled geared motor. The power supply is ensured by an energy chain or conductor line.

Special noise-insulated wheels ensure smooth running and reduced noise development. In addition, the rails can be flush with the floor and one or two chain or roller conveyors can be installed, depending on the requirements.

HÖRMANN Gruppe – KLATT Fördertechnik – Palettenförderwagen

Step-overs are required to enable or facilitate accessibility for maintenance or to reduce distances. But also due to legal safety regulations, step-overs, for example as escape routes, are planned.

The following step-overs can be used depending on the area of application:

  • Step-overs for conveyor section access
  • Step-overs without conveyor section access
  • Step-overs with platforms (step ladders, ladders)
  • Step-overs from side guide to side guide without conveyor section access and no platform
HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

Gravity roller tracks conveyors are used for horizontal transportation of the units to be moved. Due to the slight incline of the conveyor line (approx. 3-5%), the load runs solely by gravity on non-driven idlers.

Finally, brake rollers take over the controlled deceleration of the shipping units. Unloading is usually carried out using hand pallet trucks or forklifts.

HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

The roller lift station (in-floor) is used when the conveying level changes within a system. This occurs, for example, if the level rises in the course of a conveyor system after it has been fed at ground level.

By using conveyor rollers with a diameter of 60 mm, the conveyor level is +85 mm from floor level and can therefore be optimally combined with our other floor-level products.

HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

Roller conveyors are used for horizontal transportation of the units to be moved. Depending on the handling device, conveyed goods, weight and requirements, the transport unit runs over differently driven rollers. The idlers can be driven by chains or toothed belts.

For maximum stability, the base frame and the transverse distances of our roller conveyors are made of extruded aluminium with a wall thickness of 4 mm and are screwed together. The side guides can be integrated into the profile or set up as an additional guide above the scaffolding.

Thanks to vertically adjustable supports and suspensions, roller conveyors can be adapted to any kind of building requirements or adjacent conveyors

HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

Roller conveyors (in-floor) are used for horizontal transportation of the units to be moved. Due to the low conveying height, idlers with a maximum diameter of 60 mm are used.

For maximum stability, the base frame and the transverse distances of our roller conveyors are made of extruded aluminium with a wall thickness of 4 mm and are screwed together. The side guides can be integrated into the profile or set up as an additional guide above the scaffolding.

Thanks to vertically adjustable supports and suspensions, roller conveyors can be adapted to any kind of building requirements or adjacent conveyors.

HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

Roller tracks are used for manual horizontal transportation of the units to be moved.

Depending on the handling device, goods to be conveyed, weight and requirements, the shipping unit runs over rollers of different designs.

We only supply roller tracks together with a driven conveyor system.

HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

With the pallet stacker, pallets can be stacked or unstacked using the built-in lifting gear. In addition, conveyor units can be loaded or unloaded as part of a conveyor line with system pallets. A roller or chain conveyor can be installed as a load carrier. The installed load carrier depends on the goods to be transported and the transport direction.

HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen
HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen

The pallet lifter is used to connect two or more conveyor sections that are located at different levels.

The hoist is designed with toothed belts. It is driven by a three-phase motor, which can optionally be equipped with a frequency converter. For higher performance, more torque can be provided with a servo-motor in combination with a rotary encoder for positioning. For easier maintenance access, the lifter motor is mounted at the lower diverting point.

A chain conveyor is attached to the pallet lifter as a load carrier. For gap monitoring between stationary and moving conveyor technology, either light barriers or light grids are used.

HÖRMANN Gruppe Klatt Fördertechnik – Palettenförderanlagen